Sub-ohming can’t be safe..

.. for electronics, that is <img src="” class=”mceSmilieSprite mceSmilie13″ alt=”:)” title=”Smile :)” /> right? i notice even with a fan going AND a dehumidifier i still get condensation/a layer of film over some of my electronics in my man-vape-cave. Like on my cable box, i notice on the screen, the inside is foggy now, like where you see the time/channel it's on. And on my fan.. lol it actually drips water from the vapor after a few hours under the fan blades lol. This is all with a dehumidifier going as well!

I just read so many conflicting reports saying…

<a href="”>Sub-ohming can't be safe..

I’m having issues with the UWell Crown II, and it’s not good.

I purchased the Crown II yesterday afternoon. I primed and installed the .50ohm Coil and sat around 55w enjoying the great taste and cloud. I decided to change the juice and that's when all hell broke lose apparently.

Before I was done using even 3/4s of the juice I just put in the tank for the second time I got dry hits. Dry hits left and right. They got so bad I had to stop using my vaporizer for the rest of the night.

This morning I decided to change the coil with a replacement coil…

<a href="”>I'm having issues with the UWell Crown II, and it's not good.

UWell V3 Crown 2 Coil Update/Info

I purchased new Crown 2 Coils from UWell a couple days ago and they arrived today in the mail.

After seeing reviewers have a grey band around the coil and saw the black one around the ones I just ordered from UWell I gave them a call.

Spoke to a gentleman there who was friendly and told me that the grey bands that people were seeing in <a href="” rel=”nofollow”>reviews were for the reviewers only so they could differentiate between V2 and V3. All the V3 coils now being produced have the same appearance as the V2…

<a href="”>UWell V3 Crown 2 Coil Update/Info

Coverting a Smok Silenus or iTaste 134 into a mech mod?

Hi everyone, Ive dont some searching for a video or guide or even someone having done this before and I cant seem to find anything so wanted to ask, I have recently been able to get either a Smok Silenus or iTaste 134 which are both 18650 single cells but are regulated down to low watt output. I was wondering if anyone had any experience in taking these apart or where to start looking to remove the regulation and use it as an unregulated mech mod. Heck even a guide to disassembly would be great.

motley mods

I am looking in to ordering a few parts kits from motley mods…has anyone ordered from them before, I have had a hard time finding any <a href="” rel=”nofollow”>reviews for the company. They are reasonably priced and well stocked…..any input would be great!

New to mech mods, smok magneto 2 help?

So I just ordered and received my first mech mod today, the Smoktech Magneto 2. However, I'm a little bit hesitant to start using it as I'm not too educated on mech mods and battery safety. Can anyone give me advice on how to properly use a mech mod, or even how you use your smoktech magneto 2 if you own one? On hand, I currently have (besides the mod) an 18650VTC4 2100mAh 3.7V 30 amp IMR battery, an efest 18350 700mAh 3.7V (not sure on amps), as well as a double vision rda with a 0.21ohm…

<a href="”>New to mech mods, smok magneto 2 help?

lets talk uwell crown V2

Hi y'all, so i picked up the v2 crown a couple a days ago. So far, eeehh. I like the size of it, 24 mm tank, and does look nice. Comes with a preinstalled .25 ss coil and a .5 ss coil, which is nice on my rx 200. But after a couple of days i have been getting a hit like a dry hit or hotspot. But everything is looking good. Popped the pin off and inspected. Its rated 60-100 watts(which i don't believe) i ran it 60, 55, 50 and as low as 40. burnt throat hit minor sizzle from coil. Its not my…

<a href="”>lets talk uwell crown V2

Question: 3-13V to 5-15V Matek DC-DC Voltage Boost

Anyone used this before? I'm trying to build a single 26350 regulated box mod in a Hammond 1590H enclosure. I've been looking for a Voltage boosting chip that will fit in that for the longest time. Since I mainly vape at 1.8-2ohm at 4.7-5v, I barely draw 3A from the battery. Plus this is a really tiny chip.

I've searched this forum and never found any mention of this voltage booster, wondering if anyone has any experience with this? Any reason why this won't work?…

<a href="”>Question: 3-13V to 5-15V Matek DC-DC Voltage Boost